nbn FTTN explained: fibre to the node, VDSL2 and the free upgrade
5 min read · Updated Nov 2026
FTTN sends fibre to a street cabinet and uses your old phone line for the last stretch. Here's how to spot it, why distance to the cabinet sets your speed, what modem you need, and how the upgrade to full fibre works.
1
What is FTTN?
FTTN stands for Fibre to the Node. Fibre runs from the exchange to a cabinet in your street, the node, and from there your existing copper phone line carries the signal to your home. nbn did the work at the cabinet, so there's usually nothing to install inside your house. Your provider sends you a modem and you plug it in.
There's no nbn box anywhere. Your modem plugs straight into a phone wall socket with a phone cable. Apartment block with the same setup? That's probably FTTB. A white box with a fibre lead is FTTP, and one on a coax socket is HFC. Or send us your address and we'll look it up.
A VDSL2 modem-router. nbn says a modem without VDSL2 won't work here, so an old ADSL-only one is out. The modem's DSL port goes into the phone socket and the phone cable has to be a straight run: nothing in between, and no ADSL filter, which can stop the connection or slow it. If your socket is the older yellow three-prong 600-series type, you'll need an adapter. Send us your modem's make and model and we'll check it.
Phone wall socket connects by Phone cable (RJ11) into the Your modem-router's DSL.
FTTN tops out at the 100 Mbps tier, and nbn lists the range as 25 to 100 Mbps down for that tier, with the real figure depending on your line. Copper loses signal over distance. The farther your home is from the node, and the older or noisier the wiring, the slower it gets. Two neighbours on the same plan can see quite different speeds. We'll tell you what your address can honestly carry before you order.
Phone sockets, filters and wiring inside the house
FTTN uses the phone wiring already in your house, so what's plugged into it matters. Old phones, alarm units, ADSL filters and splitters on any socket can drag the line down, not just the one your modem uses. Unplug the lot and test. If you still want your home phone, plug a compatible handset into the phone port on the modem. Pulse or rotary phones don't work. Extra sockets or moving the modem to another room means a registered cabler, which can cost you.
6
Can I upgrade FTTN to full fibre?
Possibly. In January 2025, nbn announced it would offer upgrade paths to the remaining roughly 622,000 FTTN homes and businesses, with over 95 per cent able to move to FTTP and the work expected to finish by the end of 2030. It's rolling out area by area, so your street may not be ready yet. To qualify you order a plan on the 100 Mbps tier or higher, which may be faster than the plan you have now, and you'll usually need to keep it for a minimum period, often 12 months. nbn then installs the fibre alongside your existing service. Your old service stays on until you cancel it, so make sure it is. We'll check your address and tell you where you stand.
Check the phone cable is firm at the wall and in the modem's DSL port. Unplug everything else from every phone socket in the house, then restart the modem. The DSL light should go from flashing to solid within a few minutes. DSL solid but the Internet light off or red? Restart once more, and if it hasn't cleared in 10 minutes, tell us. Slow only at night, or dropping in the rain? Those patterns point at the copper, and we can raise it with nbn or check your upgrade eligibility.
FTTN is mostly a self-install. nbn finishes the connection at the node, usually without a visit to your home, and then you plug the modem into a working phone socket. If you're switching providers, allow a few business days for the changeover. Plugging in the new modem can cut off an old phone, internet or alarm service on the same line, so keep a charged mobile handy and check any monitored alarm still works over nbn. Renting? Let your landlord or agent know.